NuTech EcoSafe Strip Architectural
A non-toxic, water-based paint remover designed to safely strip architectural coatings from a variety of substrates without harmful fumes or harsh chemicals.
A non-toxic, water-based paint remover designed to safely strip architectural coatings from a variety of substrates without harmful fumes or harsh chemicals.
EcoSafe Strip Architectural is a water-based, biodegradable paint remover designed to lift architectural coatings from a wide variety of surfaces safely. Unlike harsh chemical strippers, EcoSafe Strip uses a non-toxic formula that is safer for both people and the environment. It's ideal for use in homes, commercial spaces, and sensitive areas like hospitals and schools.
Because it's water-based and non-flammable, cleanup is easy and disposal is safe. You can use EcoSafe Strip on various surfaces, including concrete, wood, metal, vinyl, and masonry. Whether you're working indoors or outdoors, it removes standard coatings, including latex, lacquers, urethanes, varnishes, and elastomeric finishes.
EcoSafe Strip is perfect for:
Additionally, it reduces downtime since other work can continue while the stripper takes effect.
| Appearance: | White Liquid |
|---|---|
| pH: | 11.14 |
| VOC Levels: | 75.5 g/L |
| Coverage Rate: | 1 – 2.2 m2/L m2/L |
This product is engineered for spray or brush application.
Airless sprayers are recommended. Use only airless equipment with chemical-resistant packing that has an output of 2 L/min and can produce a pressure of 2500 psi. A typical medium-sized airless sprayer is capable of spraying this product. Equip the sprayer with a tip size of 0.019 inches or larger. (Example: a 519 or 425 tip).
Other equipment: brushes, rollers, scraper, masking tape, plastic (polyethylene) sheet, pressure washer, electric drill with mixer, empty pails for clean-up, running water, rags. Roller applications should be used only for horizontal surfaces.
Cover/protect areas where stripping is not desired, including adjoining surfaces where overspray may travel. Polyethene sheets make a very effective barrier. If using masking tape, apply two layers of tape and remove the top layer immediately after application, as the remover may soak through the tape, damaging the paint under it. Plants should be covered or washed thoroughly with water before and during application.
Never shake EcoSafe-Strip Architectural Paint Stripper. Shaking will cause the product to separate. Using a drill mixer, mix the product until it is uniform in colour and creamy in consistency (About 1 minute per 4 litres).
Conduct a small test patch in an inconspicuous area to ensure product performance. This will indicate the time required for project completion, the suitability of the product for paint and substrate, and the most effective removal method.
Apply a thick, even layer of stripper onto the coating being removed. An airless sprayer is the most effective means of application. Always start the sprayer pump at the lowest pressure setting and slowly build up the pressure until an adequate fan pattern has been generated. High pressure and narrow tip sizes will break the stripper's emulsion and destroy its effectiveness.
The stripper must be applied 1.5 to 2 times the thickness of the removed coating, i.e. 20 mils of coating require 30-40 mils of stripper to be removed effectively. When trying to build up films thicker than 30 mils (600 microns) or applying the stripper on a glossy or greasy vertical surface, it is advisable to build the stripper film in two separate applications.
First apply a light coat of approximately 15 mils (300 microns), thick enough to hide the surface colour of the coating and allow it to dwell for 5 to 30 minutes and then build the rest of the stripper film thickness in a second application.
Once applied, leave the stripper alone, as agitation slows down penetration. If using a brush, ensure the underlying surface is completely covered with Nu EcoSafe Strip Architectural Paint Stripper.
EcoSafe Strip can be applied with a mop, roller or squeegee to remove thin-film urethanes. Dwell time is between 30 to 60 minutes. Janitorial floor machines can be used for agitation and removal of coating and stripper residue. A generous water rinse will complete the removal process.
The remover may lift the coating between weak layers if poor adhesion exists between paint layers. If this happens, remove the lifted layers with a dry scraper and re-apply with the EcoSafe Strip. Do not rinse with water between applications. While the removal process occurs, do not allow the stripper to dry on the surface. If it starts to dry, reapply the stripper.
The time required for penetration varies according to the type of paint, the thickness of the paint, and the temperature. Most paint systems require between 2 to 36 hours. Nu EcoSafe Strip Architectural Paint Stripper can be left overnight, but do not let it dry out. If you are trying to remove wax, the process should not take longer than 30 minutes to 1 hour.
Coverage is approximately 1 to 2.2 sq.m./L depending on the substrate and coating to be removed.
Above 13°C, if working in cooler temperatures, expect longer dwell time. Keep from freezing.
Removal of residue can be completed by a scraper, squeegee, mop, wet/dry vacuum system, or high-pressure washer. Be careful if using a high-pressure washer on porous surfaces, as it may damage the surface. A floor cleaning machine can also be used by going back and forth over the floor with the buffer function and then using the vacuum function to suck up the residue. For wood projects, remove lifted paint with a scraper first, then lightly rub with an abrasive nylon open web hand pad (i.e. Scotch- Brite™) to remove the remaining paint from the wood grain. Collect lifted paint and place it in plastic containers. Add Nu Ecosafe Strip Ecozorb to absorb the remaining liquids and dispose of them following local government regulations.
