Hardwearing clear sealer that provides a wet look finish for exposed aggregate
- Clear
- Durable
- Solvent Based
Description:
Wet-look sealer for aggregate and concrete surfaces.
Agreseal aggregate sealer is a deep penetrating, solvent-based acrylic sealer that provides a glossy, wet look to the aggregate. Agreseal is recommended as a two-coat system with a durable surface ideal for pedestrian and light vehicle traffic. Agreseal repels water and enhances the colour of aggregates and concrete, while protecting the surface against most stains, such as grease and oil.
Benefits:
- Improves the surface performance of the concrete
- Enhances concrete and aggregate colours
- Helps protect against freeze/thaw damage
- Protects against most stains and many household chemicals
- Repels grease, oil, and water
- Non-yellowing glossy wet look
- Low maintenance and improved cleaning
- Easily recoated
Application:
Sealing New Exposed Aggregate Surfaces:
- Etch the uncoated surface with EcoSafe Etch or EcoSafe Ultra Etch, as outlined in the relevant TDS.
- Observe ambient application conditions noted in the TDS.
- Ensure that the surface is clean and dry.
- If the surface is affected by white efflorescence, broom over with clean PaveCoat Thinners to dissolve and dissipate all salts before sealing.
- Stir thoroughly before use.
- 1st Coat: Dilute Agreseal up to 50% PaveCoat Thinners. Apply one even coat using a soft bristle broom, roller or spray at the rate of 3–5m²/L.
- 2nd Coat: Apply without solvent dilution in the same manner as the first coat.
- If an inadequate seal thickness is applied on newly exposed aggregate, some efflorescence (salt whitening) may occur. This white powder can usually be washed off easily and should cease after several months.
- The application of one or two additional coats of Agreseal can prevent the appearance of efflorescence or white salts.
Sealing & Resealing Existing Exposed Aggregate:
- Determine whether the existing aggregate has been previously sealed. Refer to the Nutech Coating Test Kit for detailed instructions or contact Nutech Paint.
- Very old, incompatible, delaminating problem sealers should be removed entirely. Stripping with EcoSafe Strip Industrial is recommended to remove all existing coatings.
- Compatible, previously sealed surfaces will require reactivation to improve inter-coat adhesion between compatible sealers. Before reactivation, the exposed aggregate surface should be free from lichen, moss, oil and other debris.
- For uncoated existing exposed aggregate, thoroughly clean using EcoSafe Degreaser and etch with EcoSafe Etch or EcoSafe Ultra Etch as outlined in the relevant TDS. Apply one even coat using a soft-bristled broom, roller, or spray at a rate of 3–5 m²/L. 2nd Coat: Apply without solvent dilution in the same manner as the first coat.
Suitable Surfaces:
Application:
Sealing New Exposed Aggregate Surfaces:
- Etch the uncoated surface with EcoSafe Etch or EcoSafe Ultra Etch, as outlined in the relevant TDS.
- Observe ambient application conditions noted in the TDS.
- Ensure that the surface is clean and dry.
- If the surface is affected by white efflorescence, broom over with clean PaveCoat Thinners to dissolve and dissipate all salts before sealing.
- Stir thoroughly before use.
- 1st Coat: Dilute Agreseal up to 50% PaveCoat Thinners. Apply one even coat using a soft bristle broom, roller or spray at the rate of 3–5m²/L.
- 2nd Coat: Apply without solvent dilution in the same manner as the first coat.
- If an inadequate seal thickness is applied on newly exposed aggregate, some efflorescence (salt whitening) may occur. This white powder can usually be washed off easily and should cease after several months.
- The application of one or two additional coats of Agreseal can prevent the appearance of efflorescence or white salts.
Sealing & Resealing Existing Exposed Aggregate:
- Determine whether the existing aggregate has been previously sealed. Refer to the Nutech Coating Test Kit for detailed instructions or contact Nutech Paint.
- Very old, incompatible, delaminating problem sealers should be removed entirely. Stripping with EcoSafe Strip Industrial is recommended to remove all existing coatings.
- Compatible, previously sealed surfaces will require reactivation to improve inter-coat adhesion between compatible sealers. Before reactivation, the exposed aggregate surface should be free from lichen, moss, oil and other debris.
- For uncoated existing exposed aggregate, thoroughly clean using EcoSafe Degreaser and etch with EcoSafe Etch or EcoSafe Ultra Etch as outlined in the relevant TDS. Apply one even coat using a soft-bristled broom, roller, or spray at a rate of 3–5 m²/L. 2nd Coat: Apply without solvent dilution in the same manner as the first coat.
Suitable Surfaces:
Tech Data Sheet
Technical Datasheet
Safety Data Sheet
Safety Datasheet
